**Verdict: REVISE**

### Status of Prior Findings ([critic.txt](file:///home/claude-agent/forge-build/forge-assets/jobs/le-mans-prototype-v1/critic.txt))

* **Rims and tires: RESOLVED.** Compared to [review-v2/final.png](file:///home/claude-agent/forge-build/forge-assets/jobs/le-mans-prototype-v1/review-v2/final.png), the wheels in [final.png](file:///home/claude-agent/forge-build/forge-assets/jobs/le-mans-prototype-v1/final.png) and [side.png](file:///home/claude-agent/forge-build/forge-assets/jobs/le-mans-prototype-v1/side.png) now use dark matte multi-spoke race rims and dark slick rubber with clear brake disc and caliper contrast.
* **Front splitter: UNRESOLVED.** In [side.png](file:///home/claude-agent/forge-build/forge-assets/jobs/le-mans-prototype-v1/side.png), the flat horizontal splitter slab still slices straight through the bottom of the front tire and protrudes behind the rear edge of the front tire tread.
* **Rear wing and shark fin: PARTIALLY RESOLVED.** The wing endplates were extended downward in [final.png](file:///home/claude-agent/forge-build/forge-assets/jobs/le-mans-prototype-v1/final.png) and [side.png](file:///home/claude-agent/forge-build/forge-assets/jobs/le-mans-prototype-v1/side.png), but the main wing plane still sits high above the roofline on tall twin struts, the shark fin stops short in mid-air well below the wing underside, and the oversized outer endplates hang outboard of the rear fenders without clean structural integration.
* **Canopy: UNRESOLVED.** Even allowing an original low angular closed cockpit rather than copying [sheet.jpg](file:///home/claude-agent/forge-build/forge-assets/jobs/le-mans-prototype-v1/sheet.jpg), the greenhouse geometry in [final.png](file:///home/claude-agent/forge-build/forge-assets/jobs/le-mans-prototype-v1/final.png) and [clay.png](file:///home/claude-agent/forge-build/forge-assets/jobs/le-mans-prototype-v1/clay.png) is unchanged from [review-v2/final.png](file:///home/claude-agent/forge-build/forge-assets/jobs/le-mans-prototype-v1/review-v2/final.png): it remains a tall, nearly full-width upright cabin with an open gap along the roof-to-window frame seam.
* **Default Paint visible finish (independent evaluation):** Although `baseColorFactor` is `.03 .03 .035` and recolors work in [paints.png](file:///home/claude-agent/forge-build/forge-assets/jobs/le-mans-prototype-v1/paints.png), the visible finish in [final.png](file:///home/claude-agent/forge-build/forge-assets/jobs/le-mans-prototype-v1/final.png), [side.png](file:///home/claude-agent/forge-build/forge-assets/jobs/le-mans-prototype-v1/side.png), and the top-left swatch of [paints.png](file:///home/claude-agent/forge-build/forge-assets/jobs/le-mans-prototype-v1/paints.png) still reads as medium metallic pewter/grey rather than deep gloss black, with stark faceted shading bands across adjacent body quads.

### Remaining Material Issues (Capped at 3)

1. **Front splitter intersects the front tires ([side.png](file:///home/claude-agent/forge-build/forge-assets/jobs/le-mans-prototype-v1/side.png)):** The lower splitter plane cuts directly through the bottom of the front tires and extends past the rear of the front wheel contact patch instead of terminating ahead of the wheel arches.
2. **Rear wing height and disconnected shark fin ([final.png](file:///home/claude-agent/forge-build/forge-assets/jobs/le-mans-prototype-v1/final.png), [side.png](file:///home/claude-agent/forge-build/forge-assets/jobs/le-mans-prototype-v1/side.png), [clay.png](file:///home/claude-agent/forge-build/forge-assets/jobs/le-mans-prototype-v1/clay.png)):** The rear wing sits well above roof height on tall swan-neck pylons, leaving the shark fin floating below the wing plane with a large vertical gap and the deep endplates hanging outboard of the rear fenders.
3. **Default paint surface shading and canopy roof seam ([final.png](file:///home/claude-agent/forge-build/forge-assets/jobs/le-mans-prototype-v1/final.png), [side.png](file:///home/claude-agent/forge-build/forge-assets/jobs/le-mans-prototype-v1/side.png), [clay.png](file:///home/claude-agent/forge-build/forge-assets/jobs/le-mans-prototype-v1/clay.png)):** Hard shading breaks across the front fenders, hood, and shark fin make the dark base coat reflect as patchy metallic grey, and a visible geometry gap remains along the top edge of the side window frame and roof header.

---

0. **Blocked on you**: nothing.
1. **What you changed**: Nothing; this was a read-only visual inspection.
2. **How you know it works**: Opened and compared [critic.txt](file:///home/claude-agent/forge-build/forge-assets/jobs/le-mans-prototype-v1/critic.txt), [sheet.jpg](file:///home/claude-agent/forge-build/forge-assets/jobs/le-mans-prototype-v1/sheet.jpg), [review-v2/final.png](file:///home/claude-agent/forge-build/forge-assets/jobs/le-mans-prototype-v1/review-v2/final.png), [final.png](file:///home/claude-agent/forge-build/forge-assets/jobs/le-mans-prototype-v1/final.png), [side.png](file:///home/claude-agent/forge-build/forge-assets/jobs/le-mans-prototype-v1/side.png), [clay.png](file:///home/claude-agent/forge-build/forge-assets/jobs/le-mans-prototype-v1/clay.png), and [paints.png](file:///home/claude-agent/forge-build/forge-assets/jobs/le-mans-prototype-v1/paints.png).
3. **What would break if you were wrong**: Passing this build would ship a car with geometry slicing through the front tires, a disconnected shark fin and towering rear wing, and faceted pewter-looking reflections on the default black paint.
4. **What you did NOT do**: Did not edit any files, inspect the Blender script or GLB mesh data, or run any renders.